Mechanical Department is well equipped with Laboratories which provides research facilities for students and faculties. The laboratory contains research equipment which helps to perform experimental research and software helps to perform simulation and modeling.
Experimental Stress Analysis Lab | |||
Sr. No. | Name of Equipment | Utility | |
1 | Transmission Polariscope | Analyzing and recording mechanical stresses and strains in components | |
2 | Reflection Polariscope | ||
Transmission Polariscope |
Reflection Polariscope |
Noise and Vibration Lab | |||
Sr. No. | Name of Equipment | Utility | |
1. | Electrodynamic Shaker 0 – 10kHz | To excite the structure for dynamic analysis. | |
3. | FFT Analyzer with Accessories Frequency Range 1Hz to 20kHz | To determine natural frequency and used for fault diagnosis. | |
4. | Hand Held Vibration Meter Frequency Range 0.2 Hz to 10 kHz Acceleration 0.1 to 240 m/s^2 | To measure overall vibration level and condition monitoring measurements. | |
6. | Sound Level Meter | To measure sound pressure level (SPL) | |
FFT Analyzer | Hand Held Vibrometer | Electrodynamic Shaker |
Tribology | |||
Sr. No. | Name of the Equipment | Utility | |
1. | Pin on Disc Tribometer with lubrication system | It is widely used for evaluation of wear of metals, ceramics, composites, polymers etc. Conforms to ASTM G 99 | |
2. | Abrasion Tester | Used in evaluation of dry abrasion resistance of metals, ceramics, polymers, coatings, composites. Conforms to ASTM G 65 | |
Pin on Disc Tribometer with Lubrication System |
Dry Abrasion Tester |
Material Science Lab | |||
Sr. No. | Name Equipment | Utility | |
1 | Magnetic Particle Testing | Non-destructive testing of ferromagnetic material | |
2 | Ultrasonic Testing | Non-destructive testing of component | |
3 | Micro-Vickers hardness Testing | To check the hardness of the material | |
4 | Optical emission spectrometer | This equipment is useful to determine the elemental composition of ferrous alloys, aluminum alloys and copper alloys. | |
5 | Image analyzer system consisting of microscope, image acquisition camera, and image analysis software. | This equipment is useful for Examination of micro structure of ferrous & nonferrous metals to determine the phases present and their amount, grain structure To measure nodularity and inclusion count and check for porosity, measure amount of graphite flakes etc. | |
6 | Digital Rockwell Hardness Tester | To check the hardness of the material on different Rockwell scales. | |
Optical emission spectrometer |
Image Analyzer |
||
Micro Vickers Hardness Testing |
Ultrasonic Testing Machine |
||
Magnetic Particle Testing |
Digital Rockwell Hardness Tester |
I.C. Engine Lab | |||
Sr. No. | Name of Equipment | Utility | |
1. | Test Rig of base and alternative fuel | Testing of 1.Computer controlled variable compression ration engine 2.Multi-cylinder petrol engine 3.Single cylinder diesel engine | |
2. | Combustion Analyzer Make: DEWE-RACK-4, DEWE-BOX-CA-EDUC, CA-OPT1, CA-ANGLE-SENSOR-0.2, CA-OPT3 | To measure 1. Crank angle based pressure diagram 2. Integrated pressure signal 3. Pressure / Volume diagram 4. Calculated heating process 5. On-line knocking recognition 6. Mathematic Setting 7. Statistical display 8. Data storing and data export to ASCII | |
3. | Two Wheeler Chassis Dynamometer Make: ATE, Maxi. 100 HP at 3000 / 6000 rpm Volumetric Fuel consumption Measurement Unit | Braked Type Chassis Dynamometer Performance Tests 1) Normal Mode Test 2) Acceleration Test 3) Braking Test 4) Average Test Plotting Performance Characteristics Curves- a. Vehicle speed v/s HP in different gears b. Vehicle speed v/s torques in different gears c. Vehicle speed v/s tractive effort | |
4. | Eddy Current Dynamometer Make : SAJ Power rating : 80 kW @ 4800 - 9000 rpm | Engine Brake Power, Torque, Specific Fuel Consumption, Air Consumption, Mechanical Efficiency, Thermal Efficiency, Friction Power, Indicated Power | |
5. | Microprocessor Based four Gases Auto. Exhaust Analyzer | Exhaust Emission Measurement of CO, HC, CO2, O2 (Petrol Engine)CO : 0-9.9 % resolution 0.1% HC : 0-9990 ppm Resolution 10 ppm CO2 : 0 - 19.9 Resolution 0.1 % O2 : 0 - 25 % Resolution: 0.1 % Response time : 10 second Warm up time: 20 min. Power Supply : 230V AC | |
6. | Smoke Meter | Exhaust Emission Measurement of Diesel engines Smoke (Diesel Engine) Display indication : light absorption coefficient (k) /% Opacity Warm up time : 15 min. Power requirement : 230 V Display range : 0-9.9 per meter | |
7. | Engine Scanner | Engine diagnostics tool (Petrol Engine) Computer controlled system engine analyzer with diesel interface, 80-column printer | |
8. | KAL Equipment | Air / Fuel ratio measurement and CO measurement (Petrol Engine)A/F ratio 8 :1 to 16: (Gasoline) A/F ratio 12 :1 to 16 : 1 (Liquid Gas) | |
Heat Power Lab | |||
1 | Sonicator | Sonication applies sound energy to agitate particles in a sample solution which can produce nano-emulsion, nano-crystals, liposomes and max emulsions also for waste water purification. | |
2 | Calorific value Measurement | Instrument helps to measure calorific value measurement of fuel | |
3 | Rheometer | Measurement of fuel viscosity | |
4 | Wind tunnel | It is used for measurement of aerodynamic characteristics of object. Using wind tunnel model we can measure aerodynamic forces, pressure distribution etc. | |
Sonicator |
Wind Tunnel |
Modeling and Simulation | ||
SN | Name of Software | Utility |
1. | CATIA V5, NX-CAD | CAD modeling and customization |
2. | ANSYS, Abacus | Finite Element Analysis |
3. | Hypermesh | Component meshing |
4. | NX-CAM | CNC Simulation and machining |
5. | Witness | Industrial layout design and optimization |
6. | TimePro | Time and motion study of industrial layout |
Other Lab Equipment | |||
Sr. No. | Name of the Equipment | Utility | |
1. | Rheometer | It is used to measure a liquid’s suspensions or slurries flow when force is applied to it. Many fluids can be tested with a rheometer when a single numerical viscosity value cannot determine them due to their components. The rheometer tests a fluid’s rheology. Characterization of Newtonian and Non-Newtonian fluids using Modular Compact Rheometer MCR-52 | |
2. | 3D Printing | It helps to create 3D model using additive manufacturing process | |
3D Printing Machine |
Rheometer |
CNC Lab | |||
Sr. No. | Name of the Equipment | Utility | |
1. | Electro-discharge Machine | It is used to machine complex components also used for die making, mold making, small drilling etc. | |
2. | CNC Lathe | It is used for machining complex cylindrical parts using computer interface. | |
Electro-discharge Machine |
CNC Lathe |